builderall

WOOD CHIPPER / SHREDDER

for the modern forestry worker

CHIPPER / SHREDDER

FOR SMALL AND BIG QUALITY JOBS!

Wood chipper HJ172

General

The new Junkkari HJ172 chipper is suitable for chipping trees less than 17 cm in diameter. It is mounted to the tractor's 3-point linkage and powered by the PTO shaft. It has a feeding angle of 45 degrees to the disc. The new infeed chute is longer, more open and the control of infeed is done by electric buttons. No-stress rotation guard comes as a standard. Junkkari HJ172 fulfills all requirements of the upcoming new chipper safety standard.

Principles

The tractor driven HJ172 is available as G- and GT models.
 

The G-model is now always equipped with 2 horizontal feeding rollers. The rollers are powered by tractor´s hydraulics and their speed can be adjusted steplessly. The feeding rollers are important especially if you chip branches or other more complicated material.
 

HJ172GT is otherwise similar than G, but it has the own hydraulic unit and therefore needs only PTO-drive from the tractor. This is usefully for instance if chipper is used with several tractors and you don't want to mix oils between them.
 

The discs comes with four knifes which you can adjust continuously depending on the desired woodchip size. The blow wings will finalize the woodchips and blow the chips effectively to the desired location through an adjustable discharge chute.
 

The new infeed chute is now longer and more open. The front part is fixed but the rear part can be easily lifted for transport. The infeed is controlled by the electric buttons on both sides of the chute. No-stress rotation guard is a standard equipment and it makes operators work easy. It automatically stops the infeed if the tractor RPM drops, reverses the wood away from the disc and then continues feeding when the RPM returns to the working level. The yellow bar around the chute guarantees the user safety. It stops the infeed immediately if it is pushed for example by body parts. 

Wood chipper HJ252

Junkkari's new HJ252 is tractor 3-point linkage mounted and manufactured according to the new safety standards. This chipper represents the most popular category and have various possibilities of use for the landscaping and bioenergy. Maximum diameter of wood is 25 cm and due to feeding angle of 45 degrees the power demand is very low. HJ252 is available as a hand feed G- and GT models as well as a crane feed version GTC.

Principles


HJ252 G is a chipper with a hydraulic feeding device. Its two feeding rollers are powered by tractor's hydraulics.
 

HJ252 GT model is almost identical to it: the only difference is that its feeding device has an independent hydraulic tank and pump. This means that no additional hydraulics is needed. This version is very useful especially if chipper is used with several tractors.
 

The new infeed chute is now longer and more open. The front part is fixed but the rear part can be easily lifted for transport. The infeed is controlled by the electric buttons on both sides of the chute. No-stress rotation guard is a standard equipment and it makes operators work easy. It automatically stops the infeed if the tractor RPM drops, reverses the wood away from the disc and then continues feeding when the RPM returns to the working level. The yellow bar around the chute guarantees the user safety. It stops the infeed immediately if it is pushed for example by body parts.

Wood chipper HJ262

Principles

HJ262 G is a chipper with a hydraulic feeding device. Its two feeding rollers are powered by tractor's hydraulics.
 

HJ262 GT model is almost identical to it: the only difference is that its feeding device has an independent hydraulic tank and pump. This means that no additional hydraulics is needed. This version is very useful especially if chipper is used with several tractors.
 

The new manual infeed chute is now longer and more open. The front part is fixed but the rear part can be easily lifted for transport. The infeed is controlled by the electric buttons on both sides of the chute. No-stress rotation guard is a standard equipment and it makes operators work easy. It automatically stops the infeed if the tractor RPM drops, reverses the wood away from the disc and then continues feeding when the RPM returns to the working level. The yellow bar around the chute guarantees the user safety. It stops the infeed immediately if it is pushed for example by body parts.

General

Junkkari's new HJ262 is tractor 3-point linkage mounted and manufactured according to the new safety standards.
 

This chipper has 90 degree feeding angle and maximum diameter of wood is 26cm.
 

The woodchip quality of these so called direct-feed chippers is extremely high, and they are especially suited for stoker boiler use because the chipper chops wood to the cross fibre. 
 

HJ262 is available as a hand feed G- and GT models as well as a crane feed version GTC.

Wood chipper HJ320C

General

Junkkari's new HJ320C is effective and compact 3-point linkage disc chipper, which will grow Junkkari's chipper range to the new level. Extremely strong frame construction has position for flange mounted crane. Disc has 4 knifes and they are steplessly adjustable like in all Junkkari models.

Infeed construction:

Discharge chute construction

Control unit:

Options:

 

Wood chipper HJ500C

The HJ500C is a powerful trailed chipper. It is excellently suited for contracting work.
 

At best, the HJ500C chipper can reach a chipping efficiency of over 100 cubic meters per hour. A high chipping efficiency and a robust infeed chute enable the use of load feeding.

The woodchips are of even quality, and the size can be adjusted as needed.

Standard equipment

Accessories

Shredder / Chipper Echo's Bear Cat SC-3013

ECHO's SC-3013 chipper/shredder takes branches, light materials and garden waste up to 3 inches in diameter and shreds it to pieces about ¾ inch thick making disposal easier. It has heavy-duty 7-gauge steel screens available in four different sizes to fit the needs of the job.

Spécifications

Chipper Capacity, Max.: 3"

Shredder Capacity, Max.: 3/4"

Engine: Briggs & Stratton

Rotor Size: 27 lbs

# of Shredder Blades: 12

Engine Displacement: 306 cc

Engine Type: 4-stroke

Start Type: Recoil only

Fuel Tank: 0.8 gal.

Oil Capacity: 37 oz

Overhead Valve: Yes

Warranty: 1 yr commercial / 3 yr consummer

Chipper / Shredder / Blower Echo's Bear Cat SC-5540B

SC5540B 5-inch PTO Chipper\ Shredder\ Blower

Get the job done and into the truck quickly and easily with the SC5540B! Heavy-duty construction, the SC5540B PTO 3-point hitch Chipper/Shredder weighs 720 pounds - this means years of dependable service. The double-banded belt drive gives a more positive transfer of power.

A great machine to move from job to job, the SC5540B is the machine landscapers and golf courses trust to clean up, move debris and make mulch. A manual-feed Chipper/Shredder without a screen reduces plugging, especially with damp material. The 20.6" x 0.75" thick, 145-pound dynamically-balanced rotor is equipped with 4 reversible chipper blades and 36 shredder knives.

NOTE - For Use On Tractors with PTO Horsepower Ratings From 25 hp to 45 hp.

Spécifications

Drive Belt: Double-Banded

Chipper Disc: 20 x .75/145 lbs., rotates at 2,000 rpm

Feed Opening: 5.5 x 5.5

Weight (lbs): 720

Warranty: 1 yr commercial / 3 yr consummer

Chipper / Shredder / Blower Echo's Bear Cat SC-5627

With the reliable Crary® Bear Cat® CH5627 Chipper, taking care of tree limbs and prunings is quick and simple. Tree services and landscaping companies use the CH5627 Chipper for jobsite cleanup, power line clearing and easement cleaning.

With the road towable hitch, the CH5627 has “go anywhere” usability. 2″ coupler standard.

The CH5627 Chipper is built with a double-banded belt drive that ensures equal transfer of power from the engine to the chipper blade, increasing the disc speed allowing the operator to chip more material at a faster pace.

The CH5627 model is designed with a range of features and options that include; flip-up jack stand that ensures machine balance during machine operation, highway towable mobility allowing this chipper to be transported to a number of worksites easily and a rotating discharge chute, letting the operator choose the direction of the discharge materials.

Battery sold separately. See Battery Usage Chart for details.

Chipper

Chipping Blades: 4 Reversible Heat-treated

Drive Type: Double-banded belt

Feed System: Gravity/Self Feed

Weight: 950 lbs

 

Trailer

Towable: Yes

Wheel Base: 44″

Wheels/Tires: ST5.3-12

Engine

Engine Make: Briggs & Stratton Vanguard®

Gross HP*: 23

Engine Displacement: 627cc

Starter Type: Electric

*Horsepower rating based on Engine Manufacturer at time of manufacture

 

Dimensions

Max Chipping Capacity: 5″

Chute Opening: 28″ x 29″

Chute Throat: 5.5″ x 6″

Rotor Size/Weight: 20″ x 1.25″/140 lbs.

L x W x H: 80″ x 57″ x 88″

Chipper / Shredder / Blower Echo's Bear Cat CH-8720iH

The ECHO Bear Cat CH8720iH is an industry unique chipper that comes with a range of features that will get any job done. The 8” Turntable Chipper features a Subaru Electronic Fuel Injected engine for greater power, high altitude operation, fast recovery time and increased fuel efficiency. The turntable design allows the operator to turn the feed hopper closer to the material or away from hazards, like road sides. This model is equipped with hydraulic feed and feature ECHO Bear Cat’s Smart Feed System. The Smart Feed System speeds up the job by automatically feeding and adjusting the feed rate without operator intervention. This will allow the operator to load more material and be able to move onto the next jobsite quickly.

Dimensions

Chipper Capacity (in): 8

L x W x H (in): 136 x 79 x 95

Weight (lbs): 2225

Chipper Disc: 30x1.25 / 275 lbs., rotates at 1,600 rpm

Feed Opening: 9 x 9

 

Chipper/Shredder

Feed System: Hydraulic

Auto Feed: Yes

Chipper Chute Opening (in): 30 x 31

Chipper Blades: 4 reversible heat treated stee chpper blades, with 4 sided adjustable anvil

Rotor Weight (lbs): 275

Discharge: Overhead

 

Engine

Fuel Type: Gas

Displacement: 720cc

Drive Belt: Triple Banded

Start Type: Electric Start

Make: EFI Subaru EH

Fuel Capacity: 9 gallons

 

Trailer

Towable: Yes

Tires: P215-75R15

Wheel Base (in): 69

Accessories

2 5/16 Inch Replacement Coupler

Blade Kit 76293-00

Chipper Low Profile Side Discharge 

Gas Tachometer

Knee Bars - Chipper

 

Warranty

Consumer: 3 Year

Commercial: 1 Year

Rental: 6 Month

 

NOTES: Illustrations may include optional equipment and accessories and may not include all standard equipment.

WOOD CHIPPER
JUNKKARI

 
 

For small and large jobs it is important to be well equipped. Junkkari wood chippersa and shredder are designed for environments that require strength. When it comes to choosing a professional wood chipper, the choice of Junkkari is a must. The Echo's Bear Cat and Junkkari range offers safe, durable and reliable equipment for individuals and contractors.

WOOD CHIPPERS AVAILABLE THROUGHOUT QUEBEC, ONTARIO AND THE MARITIMES

Gravel Distribution, a division of Les Industries Renaud Gravel, has developed a solid expertise as a manufacturer and distributor of forestry equipment throughout Quebec, Ontario and the Maritimes! Whether you own a small piece of land or are a seasoned entrepreneur who makes agroforestry your livelihood, you will find the ECHO's BEAR CAT and JUNKKARI wood chippers you need to play in the woods like the modern lumberjack you are.
Give us a call or stop by!